Water Testing

Key features Small palm-sized design Accurate from ±20 ppb ± 5% of reading Dedicated to a single parameter Uses a single AAA battery Auto Power Off after 10 minutes inactivity Built-in timer for timed reaction readings Supplied with 2 cuvettes and caps Reagent starter kit (6 packets of nitrite LR reagent) - re-ordering information: HI-707-25 1 x 1.5V AAA battery Instruction manual Specifications Range 0 to 600 ppb NO2-N Resolution 1 ppb Accuracy @ 25°C ±20 ppb ±5% of reading Light source LED @ 470 nm Light Detector Silicon photocell Method Adaptation of the EPA Diazotisation method 354.1 Environment 0 to 50°C; RH max 95% non-condensing Battery Type (1) 1.5V AAA Auto-off After ten minutes of non-use Dimensions 81.5mm x 61mm x 37.5mm Weight 64g Ordering Information HI-707 Checker® is supplied with (2) sample cuvettes with caps, nitrite LR reagent starter kit for 6 tests (6 powder reagent packets), battery, instructions and quick start guide.

Trans Instruments has specially designed the Koi Medic Salinity Tester to measure the delicate salt concentration in the pond. The Model we list measures in percentage (%) The testers are accurate and easy to use. All you need to do is turn it on and dip into the pond water. The Koi Medic Salinity Tester provides accurate results and is very easy to use, simply turn on and hold in the pond. Within a couple seconds the LCD displays the salt concentration measured in percentage. Measures accurately from 0.01% to 1%.     Specifications   Units of measurement % Range 0.00 - 1.00% Resolution 0.01% Accuracy ±0.03% Battery Type 4 x 1.5V Button Cell (Alkaline A76 or equivalent) Battery Life Approximately 150 hours (Continuous Use) Automatic Shut-off Approximately 15 minutes Temperature Compensation Automatic 0 - 50 degrees Centigrade Operating Temperature 0 - 50 degrees Centigrade Size (L x W x H) 170mm x 32mm x 15mm Weight Approximately 70 g

Key features Small palm-sized design Accurate from ±0.05ppm ± 5% of reading Dedicated to a single parameter Uses a single AAA battery Auto Power Off after 10 minutes in inactivity Built-in timer for timed reaction readings Order Information The HI-700 Checker®HC is supplied with sample cuvettes with caps (2), ammonia LR reagents starter kit x 25 tests (HI-700-25), battery, instruction manual and a quick start guide. Specifications Range 0.00 to 3.00 ppm NH3-N Resolution 0.01 Accuracy @ 25°C ±0.05 ppm ±5% of reading Light source LED @ 470 nm Light Detector Silicon photocell Method Adaptation of the ASTM Manual of Water and Environmental Technology D1426-92, Nessler Method. The reaction between ammonia and reagents causes a yellow tint in the sample. Environment 0 to 50°C; RH max 95% non-condensing Battery Type (1) 1.5V AAA Auto-off After ten minutes of non-use Dimensions 81.5mm x 61mm x 37.5mm Weight 64g Ordering Information HI-700 Checker® is supplied with (2) sample cuvettes with caps, ammonia reagent starter kit for 25 tests (1 bottle of HI-700A-0 reagent A and 1 bottle of HI-700B-0 reagents B), battery, instructions. PLEASE NOTE: In some cases, samples may contain other parameters which may interfere with results  Interference may be caused by: Hardness above 1 g/LIronSulphideGlycineVarious aliphatic and aromatic aminesOrganic chloraminesAcetoneAldehydesalcohols

Reagent for HI -707 Nitrite Marine Low Range Pocket Checker This reagent is for use with the HI-707 nitrite low range pocket checker and provides enough for 25 tests. The HI-707-25 are high-quality reagents that are pre-measured, allowing for users to achieve fast and accurate measurements with their Nitrite Low Range Checker® HC. These reagents follow the Diazotization Method in which the reaction between nitrite and reagent causes a pink tint in the sample. By simply adding the packet of HI-707-25 reagent to the sample, the reaction will take place and the HI-707 will determine the concentration from the colour that is produced. The results will be displayed in ppb of nitrite. These reagents are designed to be used with samples that have an expected range of 0 to 600 ppb nitrite. Tip for an accurate measurement It is important that the sample does not contain any debris. Whenever the cuvette is placed into the measurement cell, it must be dry outside and completely free of fingerprints, oil or dirt. Wipe it thoroughly with HI-731318 or a lint-free cloth prior to insertion. Shaking the cuvette can generate bubbles, causing higher readings. To obtain accurate measurements, remove such bubbles by swirling or by gently tapping the cuvette. Do not let the reacted sample stand for too long after reagent is added, or accuracy will be lost. After the reading, it is important to discard the sample immediately, otherwise the glass might become permanently stained.

This 25 pack of reagents is for use with the HI-700 Ammonia Low Range Pocket Checker. The HI-700-25 are high-quality reagents that are pre-measured, allowing for users to achieve fast and accurate measurements with their Ammonia Checker® HC. These reagents follow the Nessler Method in which the reaction between ammonia and reagents causes a yellow tint in the sample. By simply adding 4 drops from each bottle of HI-700-25 reagent set to the sample, the reaction will take place and the HI-700 will determine the concentration from the colour that is produced. The results will be displayed in ppm (mg/L) of ammonia-nitrogen (NH3-N). These reagents are designed to be used with samples that have an expected range of 0.00 to 3.00 ppm ammonia-nitrogen. To convert the reading to ppm of ammonia (NH3) multiply the result by 1.214. Tip for an accurate measurement It is important that the sample does not contain any debris. Whenever the cuvette is placed into the measurement cell, it must be dry outside and completely free of fingerprints, oil or dirt. Wipe it thoroughly with HI-731318 or a lint-free cloth prior to insertion. Shaking the cuvette can generate bubbles, causing higher readings. To obtain accurate measurements, remove such bubbles by swirling or by gently tapping the cuvette. Do not let the reacted sample stand for too long after reagent is added, or accuracy will be lost. After the reading, it is important to discard the sample immediately, otherwise the glass might become permanently stained.

Key features Fully portable, fitting easily into both palm and pocket 0.00 to 3.50 ppm Checker®HC is supplied with reagents for 6 tests. Use code HI-711-25 (25 tests) for future purchases. High precision results - more accurate than chemical test kits Auto shut-off feature means the Checker cannot be left on by mistake Supplied with 2 sample cuvettes Cuvette cap Starter pack of reagents x 6 (re-ordering information: HI-711-25 x 25 tests) 1 x 1.5 AAA battery Instructions Specifications Range 0.00 to 3.50 ppm Resolution 0.01 ppm (mg/L) Precision 3% of reading ±0.03 ppm (mg/L) @ 25°C Light Source LED @ 525 nm Light Detector Silicon photocell Environment 0 to 50°C (32 to 122°F); RH max 95% non-condensing Battery Type (1) 1.5V AAA Auto-off After 2 minutes of non-use and after reading Dimensions 81.5 x 61 x 37.5 mm (3.2 x 2.4 x 1.5”) Weight 64 g (2.25 oz.) Method EPA approved DPD method Standard Method 4500-Cl G. PLEASE NOTE: In some cases, samples may contain other parameters which may interfere with results Interference may be caused by: Bromine, Iodine, Ozone, Oxidised forms of Chromium and Manganese. In case of water with hardness greater than 500 mg/L CaCO3, shake the sample for approximately 2 minutes after adding the powder reagent.If the water used for this procedure has an alkalinity value greater than 250 mg/L CaCO3 or acidity value greater than 150 mg/L CaCO3, the colour of the sample may develop only partially, or may rapidly fade. To resolve this, neutralise the sample with diluted HCl or NaOH.

This 25 pack of reagents is for use with the HI-711-25 Reagents for HI-711 Total Chlorine Pocket Checker The HI-711-25 are high-quality reagents that are pre-measured, allowing for users to achieve fast and accurate measurements with their Total Chlorine Checker® HC - HI-711. These reagents follow the DPD Method in which the reaction between chlorine and reagent causes a pink tint in the sample. By simply adding the packet of HI-711-25 reagent to the sample, the reaction will take place and the HI-711 will determine the concentration from the colour that is produced. The results will be displayed in ppm (mg/L) of total chlorine. These reagents are designed to be used with samples that have an expected range of 0.00 to 3.50 ppm (mg/L) total chlorine.   Tip for an accurate measurement It is important that the sample does not contain any debris. Whenever the cuvette is placed into the measurement cell, it must be dry outside and completely free of fingerprints, oil or dirt. Wipe it thoroughly with HI-731318 or a lint-free cloth prior to insertion. Shaking the cuvette can generate bubbles, causing higher readings. To obtain accurate measurements, remove such bubbles by swirling or by gently tapping the cuvette. Do not let the reacted sample stand for too long after reagent is added, or accuracy will be lost. After the reading, it is important to discard the sample immediately, otherwise the glass might become permanently stained.