Best Sellers

Description  Aqua-Sed is based on the tried and tested active ingredient 2-phenoxyethanol, and it comes in a 250ml bottle with an easy-to-use measuring pump. It's a liquid with a very wide safety margin and has been used for anaesthetising fish for many years (reports go back to 1943). Please note that any anaesthetic a carries a risk, sometimes because the fish may have an unknown/undiagnosed problem which may cause an issue. For this reason we do not suggest the routine use of anaesthesia of koi carp for a general check-up.   How to use/dosage The dose is dependent on water volume, not on fish size. Do not put Aqua-Sed™ into the main pond or tank, it is for use in small volumes once fish are captured. Using the pump, measure the required amount into water (1 pump/litre) into a suitably sized anaesthetic container. Gently mix the slightly oily liquid into the water. Transfer the fish into this solution and observe carefully. Some initial excitement is normal in some species. The fish itself pumps the drug across its gills, administering the dose until effective. Observe the fish throughout and remove the fish when it is suitably anaesthetised for the procedure. As a general guide, gill cover movements should be slowed but not completely stopped. Following the procedure return the fish to untreated water for recovery.   Q. What temperature should the water be when using Aqua-Sed?A. Aqua-Sed will work in water of all temperatures and there is no minimum temperature it can be used at. At lower temperatures it will take longer to take effect, so please be aware of this.   Q. How should I store Aqua-Sed?A. Aqua-Sed should be stored at room temperature to prevent the liquid from becoming too thick to mix with the water.       Q. Can I use Aqua-Sed to sedate amphibians?A. Yes, you can use Aqua-Sed to sedate amphibians at the same dosage as stated for fish, However great care should be taken and under veterinary supervision as the process will take effect much quicker due to the product being absorbed through the skin.  

Reliable and economical air pumps As we all know, oxygen is vital to all aquatic inhabitants whether they are Koi, goldfish, tropical / marine fish or bacteria. The EA Air pump range provides high performance diaphragm air pumps for all fish keepers. The range was purposely developed for fish keepers to deliver that essential element into their ponds - specifically air. EA Air pumps have been tested and proven to provide the highest output at any given depth, to be economical to run and to be totally reliable. Well engineered, robust and durable, every unit has thermal protection fitted as standard.   Specifications Specification AirPump 70 Complete Kit AirPump 75 AirPump 95 AirPump 130 AirPump 150 Maximum Output lpm 70 75 95 130 150 Maximum Output (USA) 62 62 95 130 155 Output at 1m Depth - lpm 52 59 78 110 130 Output at 1m Depth - USA 52 52 78 115 135 Max. operating depth 3.2m 3.9m 4.35m 4.7m 5.5m Max. operating depth (USA) 4.2m 4.4m 4.5m 5.0m 5.6m Power Usage - Watts 34 44 62 88 106 Noise level - dBA <46 <46 <47 <50 <50 Voltage (VAC) 220 - 240V 220 - 240V 220 - 240V 220 - 240V 220 - 240V Voltage (VAC) 110 - 120V 110 - 120V 110 - 120V 110 - 120V 110 - 120V    

The OASE Pontec PondoMax is a genuine, energy-efficient, Pontec all-round talent for every garden pond! This pump is perfect for flexible implementation - for watercourses and waterfalls, as well as for filter-feed!  Stepped hose adaptor for ease of installation, accommodating flexible hose of 1", 1¼" & 1½" diameter Pumps can also be used dry mounted inline - 1.5" threaded inlet and outlet Includes a 10m power cable German engineered with a 3-year guarantee Wattage 3,500 - 45w 5,000 - 60w 8,000 - 70w 11,000 - 95w 14,000 - 140w 17,000 - 180w

This 25 pack of reagents is for use with the HI-711-25 Reagents for HI-711 Total Chlorine Pocket Checker The HI-711-25 are high-quality reagents that are pre-measured, allowing for users to achieve fast and accurate measurements with their Total Chlorine Checker® HC - HI-711. These reagents follow the DPD Method in which the reaction between chlorine and reagent causes a pink tint in the sample. By simply adding the packet of HI-711-25 reagent to the sample, the reaction will take place and the HI-711 will determine the concentration from the colour that is produced. The results will be displayed in ppm (mg/L) of total chlorine. These reagents are designed to be used with samples that have an expected range of 0.00 to 3.50 ppm (mg/L) total chlorine.   Tip for an accurate measurement It is important that the sample does not contain any debris. Whenever the cuvette is placed into the measurement cell, it must be dry outside and completely free of fingerprints, oil or dirt. Wipe it thoroughly with HI-731318 or a lint-free cloth prior to insertion. Shaking the cuvette can generate bubbles, causing higher readings. To obtain accurate measurements, remove such bubbles by swirling or by gently tapping the cuvette. Do not let the reacted sample stand for too long after reagent is added, or accuracy will be lost. After the reading, it is important to discard the sample immediately, otherwise the glass might become permanently stained.

High-performance controllable pond pumps Varipump by Evolution Aqua is a controllable pond pump, suitable for large ponds. Output and energy consumption can be controlled at the push of a button and the motor is quiet and reliable. Available in three sizes, Varipump is powerful enough to run the largest of ponds and filters, and in the most demanding of situations. Varipump is suitable for use in and out of a pond. Hosetail fittings included Specifications MODEL INLET OUTLET MAX FLOW (lph) MAX FLOW. (gph) MAX FLOW. (US gph) MAX. HEAD MAX. WATTS Varipump 10000 1½" 1½" 10,000 2,200 2,642 3.1m 75W Varipump 20000 2" 2" 20,000 4,400 5,283 5.5m 190W Varipump 30000 2" 2" 30,000 6,600 7,925 5.5m 450W Dimensions MODEL DIMENSIONS CABLE LENGTHS Varipump 10000 267mm (L) x 122mm (W) x 162mm (H) 2 metre cable from plug to control box10 metre cable from pump to control box Varipump 20000 319mm (L) x 142mm (W) x 181mm (H) Varipump 30000 370mm (L) x 155mm (W) x 205mm (H)  

Chest to fit: S 35/37" M 38/40" L 41/43" XL 44/46" Size Tolerance +/- 1"   Free DPD Next Day Delivery on orders over £50.     

Professional ultraviolet clarifiers for ponds Evolution Aqua’s pond UV clarifiers have been completely re-designed for 2021, to deliver even greater performance and improved serviceability. Our range of six evoUV pond clarifiers are made using the very latest technology and design techniques, ensuring there is even water flow through the unit, and optimum ultraviolet light penetration. One new feature is the ease of the serviceability of the evoUV. Changing bulbs, quartz sleeves or replacing a ballast are quick and simple to do. The evoUV is simple to install, with universal mounting plates allowing you to fix the unithorizontally or vertically, or at any angle you choose. Overview of Features Improves water clarity by eradicating green water High output, energy efficient ballast Fully serviceable for easy maintenance Easy to install Available in six models 2 year guarantee Specifications Model Max. pond size Max. flow rate Bulb Power Inlet/Outlet Fittings supplied 15,000 Litres3,300 UK Gallons3,963 US Gallons 7,500 Litres/hr1,650 UK Gallons/hr1,982 US Gallons/hr 15W(1 x 15W T8) 1½" 2 x 1½"Threaded Hosetails 20,000 Litres4,400 UK Gallons5,284 US Gallons 10,000 Litres/hr2,200 UK Gallons/hr2,642 US Gallons/hr 25W(1 x 25W T8) 1½" 2 x 1½"Threaded Hosetails 30,000 Litres6,600 UK Gallons7,925 US Gallons 15,000 Litres/hr3,300 UK Gallons/hr3,962 US Gallons/hr 30W(1 x 30W T8) 1½" 2 x 1½"Threaded Hosetails 55,000 Litres12,100 UK Gallons14,530 US Gallons 20,000 Litres/hr4,400 UK Gallons/hr5,284 US Gallons/hr 55W(1 x 55W T8) 1½" 2 x 1½"Threaded Hosetails 75,000 Litres16,500 UK Gallons19,815 US Gallons 25,000 Litres/hr5,500 UK Gallons/hr6,605 US Gallons/hr 75W(1 x 75W T8) 1½" 2 x 1½"Threaded Hosetails 75,000 Litres16,500 UK Gallons19,815 US Gallons 25,000 Litres/hr5,500 UK Gallons/hr6,605 US Gallons/hr 110W(2 x 55W T8) 2" No Fittings Supplied How the evoUV works The evoUV range of clarifiers have been designed to clear green water which is caused by single celled green algae and prevent it from returning. They will work alongside many different filtration systems but when used alongside Evolution Aqua’s pond filtration systems, the evoUV will help to deliver crystal clear and healthy pond water. Your evoUV professional quality UV can be connected to your pond pump and filter with flexible hose using the stepped hosetails provided, or you can install the unit using hard pipe. Installing the evoUV PUMP-FED INSTALLATION Install evoUV before the filter on the pipework run from the pond GRAVITY-FED INSTALLATION Install evoUV after the filter on the return to pond pipework run. Dimensions evo15 and evo25 The overall dimensions of evo15 and evo25 are identical. They are 540mm (l) x 116mm (w) x 153mm (h) excluding hosetails. The distance between the centre of the inlet and the centre of the outlet is 319mm. The evo15 uses a standard length 15W T8 UV bulb and the evo25 uses a standard 25W T8 UV bulb. evo30 and evo55 The overall dimensions of evo30 and evo55 are identical. They are 990mm (l) x 85mm (w) x 153mm (h) excluding hosetails. The distance between the centre of the inlet and the centre of the outlet is 768.5mm. The evo30 uses a standard length 30W T8 UV bulb and the evo55 uses a standard 55W T8 UV bulb. evo75 The overall dimensions of evo75 are 1293mm (l) x 85mm (w) x 153mm (h) excluding hosetails. The distance between the centre of the inlet and the centre of the outlet is 1071.5mm. The evo75 uses a standard length 75W T8 UV bulb. evo110 The overall dimensions of evo110 are 990mm (l) x 195mm (w) x 280mm (h). The distance between the centre of the inlet and the centre of the outlet is 768.5mm. The evo110 uses two standard length 55W T8 UV bulbs.

Pre-filter to remove waste & debris The Cetus sieve is a bow screen pre-filter, made using the latest rotational molding technology. With all of its benefits and build quality, it is undoubtedly the best of its kind on the market today, regarding quality and performance! It is designed to efficiently and effectively remove large amounts of mechanical waste from a pond. It can be set-up gravity OR pump fed and has many benefits over the original bow screen technology. Overview The Cetus Sieve is a self-adjusting sieve which can be installed either gravity fed or pump fed. The Cetus Sieve enables your pond water to be filtered of large amounts of waste and debris before the water enters your current filter system. This process is commonly referred to as “pre-filtering”. The Cetus Sieve can also be used as a stand-alone unit to remove leaves and other floating debris from your pond via a surface skimmer. The Cetus Sieve will efficiently and effectively remove large amounts of mechanical waste from your pond. The Cetus Sieve is compatible with all filtration systems, however it is the perfect prefilter for the Evolution Aqua Nexus filter range. For gravity fed systems the Cetus Sieve has a weir which will automatically adjust to the flow rate of your pump. (Max flow rate 18,000 litres/hr) When the Cetus Sieve is used in front of any other biological/mechanical filter the period in between cleaning will be extended. The biological process is improved by the removal of organic matter which would consume oxygen and leach ammonia and other compounds into the water. Specifications Model Max. flow rate Inlet - Gravity Fed Inlet - Pump Fed Outlet - Gravity Fed Outlet - Pump Fed 18,000 Litres/hr4,000 UK Gallons/hr4,755 US Gallons/hr 110mm/4" 50mm/1½" 1½" 3" Dimensions How the Cetus Sieve works Installing the Cetus Sieve The Cetus Sieve has a variable inlet height using the unique patented Pondflow regulation system – for use when gravity fed. This allows water levels within the pond to drop without causing the circulating pump to be starved of water. The Cetus will allow a skimmer or a bottom drain to accept vast amounts of waste without excessive cleaning needed to be carried out. The water must then be pumped to either a normal filter above pond level (Nexus Eazy/Eazy Pod) or to a pressurised filter. If pump fed, the sieve is placed above pond water level and then the exit water is gravity dropped into your main filter. The Cetus sieve is a bow screen pre-filter, suitable for pre-filtration of any biological filter including all pressured filters. It is advised that all pressurised filters be pre-filtered using a Cetus to reduce excessive backwashing and maintenance due to heavy solids. Installing the Cetus Sieve The Cetus Sieve has a variable inlet height using the unique patented Pondflow regulation system – for use when gravity fed. This allows water levels within the pond to drop without causing the circulating pump to be starved of water. The Cetus will allow a skimmer or a bottom drain to accept vast amounts of waste without excessive cleaning needed to be carried out. The water must then be pumped to either a normal filter above pond level (Nexus Eazy/Eazy Pod) or to a pressurised filter. If pump fed, the sieve is placed above pond water level and then the exit water is gravity dropped into your main filter. The Cetus sieve is a bow screen pre-filter, suitable for pre-filtration of any biological filter including all pressured filters. It is advised that all pressurised filters be pre-filtered using a Cetus to reduce excessive backwashing and maintenance due to heavy solids. The Cetus Sieve has a variable inlet height using the unique patented Pondflow regulation system – for use when gravity fed. This allows water levels within the pond to drop without causing the circulating pump to be starved of water. The Cetus will allow a skimmer or a bottom drain to accept vast amounts of waste without excessive cleaning needed to be carried out. The water must then be pumped to either a normal filter above pond level (Nexus / Eazy Pod) or to a pressurised filter. If pump fed, the sieve is placed above pond water level and then the exit water is gravity dropped into your main filter. The Cetus sieve is a bow screen pre-filter, suitable for pre-filtration of any biological filter including all pressured filters. It is advised that all pressurised filters be pre-filtered using a Cetus to reduce excessive backwashing and maintenance due to heavy solids. GRAVITY-FED INSTALLATIONS GRAVITY-FED INSTALLATIONS PUMP-FED INSTALLATIONS

Soft against the skin and comfortable to wear. 80% Cotton 20% Polyester. Machine wash according to instructions on the label. Regular fit.  A black sweatshirt with a small sleek Koi on the front. The back is blank.    Chest to fit: S 35/37" M 38/40" L 41/43" XL 44/46" Size Tolerance +/- 1"   Free DPD Next Day Delivery on orders over £50.   

Create a safer environment for your fish The Evolution Aqua Detox Dechlorinator is a quick and simple method of filtering out harmful chlorine and other impurities from tap water. It is ideal for first fill, water changes and top-ups, for both ponds and aquariums. There’s no need to wait for chlorine to “gas-off” or to use liquid treatments. Simply fill up straight from the hosepipe via the Evolution Aqua Detox Dechlorinator. This unit simply connects to garden hose or rigid pipe work. Connectors are included. Hi-grade activated carbon removes chlorine, chloramine, bromine, malachite green, dyes, colours, humic acids, organics, proteins, antibiotics, hormones and ozone. 2 Sizes Available Recommended flow rate: 4 litres per minute. The 30 inch high-grade activated carbon filter will treat up to*:550,000 Litres / 122,083 U.K. Gallons / 146,615 U.S. Gallons The 12 inch high-grade activated carbon filter will treat up to*:225,000 Litres / 49,493 U.K. Gallons / 59,439 U.S. Gallons *Maximum treatable water is based on incoming 0.5ppm chlorine.

Innovative Polisher For Ponds   The NEW Tempest Filter is an innovative polishing system for ponds. The Tempest Filter uses our latest filtration media, K+Media, to deliver crystal clear, healthy water. Designed to be used in conjunction with any filtration system, the Tempest Filter offers additional mechanical and biological filtration. The Tempest Filter can be installed on a variety of set-ups and can be used on quarantine systems or as astandalone filter on smaller ponds up to 5,000 Litres / 1,100 Gallons. Independently Tested Filter Media   Using Evolution Aqua’s K+Media as the filter media, particles down to one micron can be filtered. On a single pass, testing has proven our media capable of removing all particles down to 25 micron when used at the optimum flow rate. Not only that, K+Media is the result of extensive research and development and is moulded with minerals for faster maturation times.      Evolution Aqua filter media has been independently tested by Cranfield University and the IFTS (Institut de la Filtration et des Techniques Séparatives). IFTS International Filter Testing Services is the international reference for solid-liquid separation. Founded in 1981, IFTS is an independently regulated, ISO 17025 accredited, laboratory and research center focusing on liquid filtration and separation science. IFTS quality management system is certified to ISO 9001:2015. How The Tempest Filter Works   Water is pumped up through the Tempest Filter. The K+Media moves to the top of the filter, becoming a mechanical barrier that traps debris as it flows through the system. Waste is trapped in the K+Media until the cleaning cycle dislodges it and it gets flushed away. How To Clean The Tempest Filter   The Tempest Filter can be cleaned in matter of minutes, by simply turning the pump off, closing slide valves and opening the waste valve tap.   Specifications   Max Pond Size Inlet Outlet Drain Size Max Flow Rate Optimum Flow Rate Volume of Water in Filter Dimensions Amount of K+Media Supplied 5,000 Litres1,100 UK Gallons1,320 US Gallons 1½” UK / USA50mm EU 1½” UK / USA50mm EU 1” UK / USA32mm EU 7,500 Litres/hr1,650 UK Gallons/hr1,980 US Gallons/hr 5,000 Litres/hr1,100 UK Gallons/hr1,320 US Gallons/hr 27 Litres5.9 UK Gallons7.1 US Gallons 1055mm x 250mm x 205mm 7 Litres Installing the Tempest Filter There are a number of ways the Tempest Filter can be installed on your pond system. Below are some typical installation ideas. PLEASE NOTE: The slide valves fitted to the Tempest Filter allow connection to 1½” pressure pipe. If installing the Tempest Filter using flexible hose you will need to fit a reducing sleeve (EA Code: M35-050) and a 1½” solvent weld stepped hosetail (EA Code: HOSETAIL15) inside each slide valve. To allow the Tempest Filter to give the best performance, it is important that the flow rate is no more than the 5,000 litres per hour. Some of the installation examples show aby-pass that will enable you to increase the flow through the pond.   TYPICAL INSTALLATION WITH A GRAVITY-FED FILTER You can install a Tempest Filter after a primary filter on a gravity-fed set-up, such as the Nexus+, and after a UV Clarifier, such as an evoUV. The slide valves on the Tempest Filter enable connection to 1½” pressure pipe. The installation example shown below has a by-pass that will enable you to increase the flow through your pond while maintaining the optimum flow through the Tempest Filter. Installing ball valves on the pipe work will help you regulate the flow. The return from the Tempest can go back to the centre of your Nexus+ or back into the pond.   TYPICAL INSTALLATION ON A PRESSURISED SYSTEM You can install a Tempest Filter on a pressurised system with a K1 Micro Bead, Nexus+, EazyPod. The slide valves on the Tempest Filter enable connection to 1½” pressure pipe. The installation example shown below has a by-pass that will enable you to increase the flow through your pond while maintaining the optimum flow through the Tempest Filter. Installing ball valves on the pipe work will help you regulate the flow. The return from the Tempest and the K1 Micro Bead go back to the pond.   TYPICAL STANDALONE TEMPEST FILTER INSTALLATION   You can install a Tempest Filter on a quarantine system, or a standalone pond up to 5,000 litres, at the side of a pond or above the pond. The slide valves on the Tempest Filter enable connection to 1½” pressure pipe. If installing the Tempest Filter using flexible hose you will need to fit a reducing sleeve (EA Code: M35-050) and a 1½” solvent stepped hosetail (EA Code: HOSETAIL15) inside each slide valve. TYPICAL SKIMMER LINE INSTALLATION   You can install a Tempest Filter on a skimmer line. The slide valves on the Tempest Filter enable connection to 1½” pressure pipe. If installing the Tempest Filter using flexible hose you will need to fit a reducing sleeve(EA Code: M35-050) and a 1½” solvent stepped hosetail (EA Code: HOSETAIL15) inside each slide valve.   MODULAR TEMPEST FILTER INSTALLATION   On larger systems that require a higher flow rate, multiple Tempest Filters can be installed in a modular system. The slide valves on the Tempest Filter enable connection to 1½” pressure pipe. If installing the Tempest Filter using flexible hose you will need to fit a reducing sleeve (EA Code: M35-050) and a 1½” solvent stepped hosetail (EA Code: HOSETAIL15) inside each slide valve. It is important that each Tempest Filter can be isolated using the slide valves so that cleaning can be carried out independently. Although on the installation diagram below we show two filters into one return line, independent return lines will allow you to observe the flow rate through both Tempest Filters and balance accordingly.   Dimensions   New advanced filtration media Plastic media, for use in biological pond filters - specifically in moving bed bio reactors, was pioneered by Evolution Aqua, some 20 years ago. In recent years, other plastic media have come onto the market, usually with the aim of trying to get more and more surface area. However, one drawback to using plastic media has always been the time it takes to establish a stable biofilm – essential for good filtration.  After many years of research, Evolution Aqua have now developed a new media that not only gives class leading surface area, but also overcomes the problem of long maturation times. K+Media is designed and manufactured in the UK by Evolution Aqua. This advanced media, with its innovative design, and class leading surface area provides enhanced biological and mechanical filtration.  As Evolution Aqua extrude K+Media, Minerals and Enzymes are added to the raw material. The result of this process, unique to Evolution Aqua, is a filtration media that not only outperforms most of its competitors due to its large protected surface area, but also answers the problem of how to speed up the time taken to mature your filter.

Complete filtration with UVC A compact member of the Nexus family, the EazyPod Complete is a mechanical and biological filter system for garden ponds up to 10,000 litres. The EazyPod Complete utilises static K1 Micro, which provides enhanced biological benefits, even when using the EazyPod Complete solely as a mechanical waste filter. Available in Grey or Granite Green colours. Overview Unlike the EazyPod and EazyPodAir, the EazyPod Complete benefits from having an integrated 18 Watt UVC built in to the inlet section of the filter. This makes it a complete filter system in one, helping to eradicate green water, therefore delivering crystal clear and healthy water for your fish. Specifications Model Max Pond Size Ornamental Fish Max Pond Size with Koi Max Feed Rate Volume of water in filter Max flow rate Recommended air pump UV-C bulb 10,000 Litres2,200 Gallons2,640 Us Gallons 10,000 Litres2,200 Gallons2,640 US Gallons 100 - 125g Per Day 80 Litres18 Gallons21 US Gallons 10,000 Lph2,200 Gph2,640 US Gph Air Pump 70 Kit (Not supplied) x 10,000 Litres2,200 Gallons2,640 US Gallons 10,000 Litres2,200 Gallons2,640 US Gallons 100 - 125g Per Day 80 Litres18 Gallons21 US Gallons 10,000 Lph2,200 Gph2,640 US Gph Air Pump 70 Kit (supplied) x 10,000 Litres2,200 Gallons2,640 US Gallons 10,000 Litres2,200 Gallons2,640 US Gallons 100 - 125g Per Day 80 Litres18 Gallons21 US Gallons 10,000 Lph2,200 Gph2,640 US Gph Air Pump 70 Kit (supplied) 18 W PL-L Dimensions How the EazyPod Complete works Water from the pond enters the EazyPod Complete via the inlet, cascading around the 18 Watt UV-C bulb, where any algae will be exposed to the UV-C radiation. The water then flows around the circumference of the outer chamber of the EazyPod Complete, passing through the stainless steel grill causing many of the larger solids to be filtered out and settle in the base of the outer chamber. This is the first stage of mechanical filtration. As water enters the central chamber, through the stainless steel grill, the fine smaller solids become trapped in the mass of K1 Micro. Bio-films build up on the protected surface area within each piece of media, allowing biological filtration to take place. After passing through the K1 Micro, the clean water then rises and overflows into the inner return pipe and flows back to the pond via the outlet. The EazyPod Complete is incredibly simple to clean. The connected air pump is used during the cleaning cycle to agitate the K1 Micro to free up any debris and waste that has built up within the filter. All EazyPod Complete models are supplied with a 70 litre per minute air pump and accessory kit. Installing the EazyPod Complete Water from the pond enters the EazyPod Complete via the inlet, cascading around the 18 Watt UV-C bulb, where any algae will be exposed to the UV-C radiation.The water then flows around the circumference of the outer chamber of the EazyPod Complete, passing through the stainless steel grill causing many of the larger solids to be filtered out and settle in the base of the outer chamber. This is the first stage of mechanical filtration.As water enters the central chamber, through the stainless steel grill, the fine smaller solids become trapped in the mass of K1 Micro. Bio-films build up on the protected surface area within each piece of media, allowing biological filtration to take place.After passing through the K1 Micro, the clean water then rises and overflows into the inner return pipe and flows back to the pond via the outlet.The EazyPod Complete is incredibly simple to clean. The connected air pump is used during the cleaning cycle to agitate the K1 Micro to free up any debris and waste that has built up within the filter.All EazyPod Complete models are supplied with a 70 litre per minute air pump and accessory kit. Installing the EazyPod Complete PUMP-FED INSTALLATION ONLYBy this we mean that if your pump is going to be used to supply the water to the filter, and the filtered water then returns back into your pond via gravity, i.e. down a waterfall, or through a large diameter pipe, this is referred to as PUMP FED (i.e. the water is fed to the filter using a pump).

Advanced filtration systems for Koi ponds now with NEW K+Media Evolution Aqua have launched the Nexus320+ and Nexus220+filtration systems. Building on the tried and tested technology that has been ever present in the world renowned Nexus, the team at Evolution Aqua have gone even further to enhance their number one Koi pond filter. The Nexus320+ and Nexus220+ filters now come with a new filter media called K+Media in the moving bed outer chamber for vastly improved biological filtration and faster filter maturation. The new Nexus+ filters are also supplied “auto ready”, with factory fitted fixings already in place, making it even easier to upgrade to the Nexus Automatic Cleaning System.   Maximum pond size: 18,000 litres / 4,000 gallonsRecommended flow rate: 6,000 litres per hourMaximum flow rate: 10,000 litres per hourVolume of water in Nexus: 510 litresAmount of K1 Micro in EAZY: 18 litresAmount of K+Media supplied: 50 litresMaximum amount of K+Media: 150 litres   Maximum pond size: 34,000 litres / 7,500 gallonsRecommended flow rate:11,000 litres per hourMaximum flow rate:13,000 litres per hourVolume of water in Nexus:840 litresAmount of K1 Micro in EAZY:20 litresAmount of K+Media supplied:100 litresMaximum amount of K+Media:300 litres How the Nexus+ Works The Nexus+ filter is an innovative biological and mechanical filter system in one. Water from the pond enters the Nexus+ via the inlet into the inner chamber which works as a vortex allowing larger solids to settle out. The water then passes through Eazy filter, where finer particles are removed at the mechanical stage of filtration, thanks to the static bed of K1 Micro filter media.The mechanically clean water then passes to the outside chamber of the Nexus+ where the new K+Media Moving Bed is located for biological treatment prior to being returned to the pond. At this stage, biological breakdown occurs through different strains of bacteria and filter feeders living on the vast protected surface area of each piece of the K+Media. These bacteria convert Ammonia and Nitrite into less harmful Nitrate. Water then passes through the exit grill into the outlet, returning back to the pond. Nexus+ Dimensions Installing the Nexus+ The Nexus+ MUST be installed on a solid, level base, a minimum of 1.2 metres x 1 metre. Failure to do this will cause irreparable damage to the filter and will therefore invalidate your warranty.   GRAVITY-FED INSTALLATIONS By this we mean that your pump is going to be used to return the filtered water to the pond and therefore your filter will be supplied by gravity via a larger diameter pipe. In this situation the water level in the filter will be at the same level as the pond.  PUMP-FED INSTALLATIONS By this we mean that if your pump is going to be used to supply the water to the filter, and the filtered water then returns back into your pond via gravity, i.e. down a waterfall, or through a large diameter pipe, this is referred to as PUMP FED (i.e. the water is fed to the filter using a pump). Specifications Model Max Pond Size Max Flow Rate Volume of Water in Nexus Amount of K1 Micro in Eazy Chamber Amount of K+Media supplied in Bio-chamber Max Capacity for K+Media 18,000 litres4,000 UK Gallons4,800 US Gallons 10,000 litres/hour2,200 UK Gallons/hr2,640 US Gallons/hr 510 litres112 UK Gallons135 US Gallons 18 litres of K1 Micro inside the Eazy 50 litres of K+Media in the bio-chamber 150 of K+Media in the bio-chamber 34,000 litres7,500 UK Gallons9,000 US Gallons 13,000 litres/hour2,859 UK Gallons/hr3,431 US Gallons/hr 840 litres185 UK Gallons222 US Gallons 20 litres of K1 Micro in the Eazy 100 litres of K+Media in the bio chamber 300 litres of K+Media in the bio chamber New advanced filtration media Plastic media, for use in biological pond filters - specifically in moving bed bio reactors, was pioneered by Evolution Aqua, some 20 years ago. In recent years, other plastic media have come onto the market, usually with the aim of trying to get more and more surface area. However, one drawback to using plastic media has always been the time it takes to establish a stable biofilm – essential for good filtration.  After many years of research, Evolution Aqua have now developed a new media that not only gives class leading surface area, but also overcomes the problem of long maturation times. K+Media is designed and manufactured in the UK by Evolution Aqua. This advanced media, with its innovative design, and class leading surface area provides enhanced biological and mechanical filtration.  As Evolution Aqua extrude K+Media, Minerals and Enzymes are added to the raw material. The result of this process, unique to Evolution Aqua, is a filtration media that not only outperforms most of its competitors due to its large protected surface area, but also answers the problem of how to speed up the time taken to mature your filter. Minerals added for faster filter maturation  During the extrusion process, Evolution Aqua add a range of minerals, along with magnesium, calcium, enzymes and salt to the raw material that is used to manufacture K+Media. The result means that K+Media will mature much faster than many other types of media. - The addition of these minerals creates a rough surface on the media. This textured surface has a microscopic honeycomb of peaks and craters that allow waste particles to collect, and nitrifying bacteria to form. - The minerals act as a food source for the bacteria, helping the bacteria to develop and multiply at a faster rate, further improving maturation times. - Calcium alone has proven advantages for developing and maintaining effective bio-films. - The enzymes that are added also help to make the media “sticky” so waste particles can adhere to media easier. - Salt is added during the extrusion process, which is dissolved during the cooling process, leaving a rough surface on which bio-film can easily adhere. Increased surface area  With a new shape and profile, K+Media has also been designed to have an increased and class leading surface area, meaning an overall surface area of 1,350m2 per m3. More importantly for biological filtration, the protected surface area of K+Media is 1,025m2 per m3.  This allows a stable bio-film to form and remain intact when used in moving bed biological filtration, as in the new Nexus+. Stable bio-film development The shape of K+Media optimises the amount of “quiet zones” within the media where a stable bio-film can develop. Whilst K+Media keeps the integral profile of K1 Media at its core, there is an extra layer of cells and fins around the outside of each piece that enable microscopic organisms such as Rotifers and Vorticella to thrive. This is an additional benefit as competitor media do not have such “quiet zones” that would allow these higher lifeforms of filter feeders to develop. The bacteria and organisms that form within the bio-film ensure the media delivers optimum levels of biological filtration in the moving bed, which has been proven filtration technology for many years in the fishkeeping hobby. Use with PURE Pond products  Evolution Aqua also recommend using K+Media in combination with the PURE Pond and PURE+ Filter Start Gel to boost bacteria levels which in turn will stick to the media and speed up the maturation process even more.   Do I need an airpump for NexusPlus? Yes, it powers the moving bed biological filter and is also vital to the cleaning process. You need an Evolution Aqua Air Pump 75 for a Nexus 220 and an Air Pump 95 for a Nexus 320. If you increase the amount of media in the outer chamber you may well need a more powerful airpump. The correct size airpump to enable the filter media to move is detailed in the below: 50 - 75 litres = Use an Air Pump 75 75 - 100 litres = Use an Air Pump 95 100 - 150 litres = Use an Air Pump 130 150 - 300 litres = Use an Air Pump 150

DOB: 2023 Sex: Male Bloodline: Sakai     This fish has been spawned from high-quality Japanese parents. Cuttlebrook Koi Farm has been breeding and growing Koi at their farm since it was first built in 1990. Over the years they have developed a reputation for producing the finest quality Nishikigoi.

DOB: 2023 Sex: Female Bloodline: Omosako     This fish has been spawned from high-quality Japanese parents. Cuttlebrook Koi Farm has been breeding and growing Koi at their farm since it was first built in 1990. Over the years they have developed a reputation for producing the finest quality Nishikigoi.

DOB: 2023 Sex: Female Bloodline:    This fish has been spawned from high-quality Japanese parents. Cuttlebrook Koi Farm has been breeding and growing Koi at their farm since it was first built in 1990. Over the years they have developed a reputation for producing the finest quality Nishikigoi.

DOB: 2022 Sex: Female Bloodline:       This fish has been spawned from high-quality Japanese parents. Cuttlebrook Koi Farm has been breeding and growing Koi at their farm since it was first built in 1990. Over the years they have developed a reputation for producing the finest quality Nishikigoi.

DOB: 2022 Sex: Male Bloodline: Isa     This fish has been spawned from high-quality Japanese parents. Cuttlebrook Koi Farm has been breeding and growing Koi at their farm since it was first built in 1990. Over the years they have developed a reputation for producing the finest quality Nishikigoi.